Part Number Hot Search : 
527225LF PWR6006 AN2989 KTC1003 MB91F46 C3120 KTC1003 74HC40
Product Description
Full Text Search
 

To Download 1SMB2EZ60 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  page . 1 stad-jul.16.2005 1smb2ez6.8~1smb2ez100 features ? low profile package ? built-in strain relief ? low inductance ? typical i d less than 1.0a above 11v ? plastic package has underwriters laboratory flammability classification 94v-o ? high temperature soldering : 260c /10 seconds at terminals ? pb free product are available : 99% sn can meet rohs environment substance directive request mechanical data case: jedec do-214aa, molded plastic over passivated junction terminals: solder plated, solderable per mil-std-750, method 2026 polarity: indicated by cathode band standard packing: 12mm tape (e1a-481) weight: 0.003 ounce, 0.093 gram glass passivated junction silicon zener diodes notes: a.mounted on 5.0mm 2 (.013mm thick) land areas. b.measured on 8.3ms, and single half sine-wave or equivalent square wave ,duty cycle=4 pulses per minute maximum .185(4.70) .220(5.59) .096(2.44) .083(2.11) .155(3.94) .008(.203) .050(1.27) .012(.305) .160(4.06) .200(5.08) .083(2.13) .075(1.91) .130(3.30) .002(.051) .030(0.76) .006(.152) smb/do-214aa unit: inch (mm) voltage 6.8 to 100 volts power 2.0 watts maximum ratings and electrical characteristics ratings at 25c ambient temperature unless otherwise specified. r e t e m a r a pl o b m y s e u l a vs t i n u 0 5 = a t n o n o i t a p i s s i d r e w o p e s l u p k a e p o ) a s e t o n ( c 0 7 e v o b a e t a r e d o c p d 0 . 2 0 . 4 2 s t t a w / w m o c e v a w - e n i s f l a h e l g n i s s m 3 . 8 t n e r r u c e g r u s d r a w r o f k a e p ) d o h t e m c e d e j ( d a o l d e t a r n o d e s o p m i r e p u s i fsm 5 1s p m a e g n a r e r u t a r e p m e t e g a r o t s d n a n o i t c n u j g n i t a r e p o t j t , stg 0 5 1 + o t 5 5 - o c
page . 2 stad-jul.16.2005 1smb2ez6.8~1smb2ez100 r e b m u n t r a p e g a t l o v r e n e z l a n i m o n e c n a d e p m i r e n e z m u m i x a m e s r e v e r . x a m t n e r r u c e g a k a e l g n i k r a m e d o c e g a k c a p v z @i zt z zt @i zt i zt z zk @i zk i zk i r @v r v . m o n v . n i m v . x a m s m h o a m s m h o a m
page . 3 stad-jul.16.2005 1smb2ez6.8~1smb2ez100 application note: since the actual voltage available from a given zener diode is temperature dependent, it is necessary to determinejunction temperature under any set of operating conditions in order to calculate its value. the following procedure is recommended: lead temperature, t , should be determined from: t= lap +t l is the lead-to-ambient thermal resistance ( c/w) and pd is the power dissipation. the value for l will vary and depends on the device mounting method. l is generally 30-40 c/w for the various clips and tie points in common use and for printed circuit board wiring. the temperature of the lead can also be measured using a thermocouple placed on the lead as close as possible to the tie point. the thermal mass connected to the tie point is normally large enough so that it will not significantly respond to heat surges generated in the diode as a result of pulsed operation once steady-state conditions are achieved. using the measured value of tl, the junction temperature may be determined by: t=t+ t t is the increase in junction temperature above the lead temperature and may be found from figure 2 for a train of power pulses or from figure 10 for dc power. t=jp for worst-case design, using expected limits of i , limits of p and the extremes of t ( t ) may be estimated. changes in voltage, v , can then be found from: v= v t v , the zener voltage temperature coefficient, is found from figures 5 and 6. under high power-pulse operation, the zener voltage will vary with time and may also be affected significantly by the zener resistance. for best regulation, keep current excursions as low as possible. data of figure 2 should not be used to compute surge capa-bility. surge limitations are given in figure 3. they are lower than would be expected by considering only junction temperature, as current crowding effects cause temperatures to be extremely high in small spots resulting in device degradation should the limits of figure 3 be exceeded. l lda a a a jl jl jl z           o o jl l d zd jj z zj 1 2 3
page . 4 stad-jul.16.2005 1smb2ez6.8~1smb2ez100 4 5 6 7 range 8


▲Up To Search▲   

 
Price & Availability of 1SMB2EZ60

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X